The more detailed the better, as long as the edge and veneer veneer detailed steps, other steps do not use.
The answer to the 80home fashion furniture is very standardPlate sanding refers to the customer will need to add the wood edge or due to stitching caused by surface roughness of substrate enough through the wide breadth sanding machine for sanding processing, mainly in order to achieve the purpose of smooth surface for hot pressing plate is not uniform throughout the compression of thick sand is light foaming. An attached sander function, sometimes plate thickness does not meet the regular customer needs, only by sanding again and again to reduce the thickness of the thickness of demand until close to the customer so far. Because the accurate thickness of sanding machine can be accurate to about 10S, so with the caliper can reach the thickness of purpose.A process is in fact in the preparation of the veneer veneer veneer cutting industry. Because of the impact of natural conditions, the conventional width veneer are generally restricted in a dozen centimeters (some more narrow, of course there are some more wide), so must pass before veneer and veneer edge stitching, there will be a lot of white edge (also is the color difference and the middle) if you do not cut off together will be very ugly, in order to make the stitching seam is not too obvious to do so to seal, then as long as two edges to splice line can be better. There are special cutting veneer veneer cutting general machine, cutting machine blade length of two or three meters, basically can satisfy the needs of
1.: edgeThe manual or automatic edge banding machine edge, can also manually edge, no matter what kind of program are: edge, edge or edge glue - edgeband pressure post in edge - edge - on both sides of the extra redundant block edge trimming - dressing for automatic sealing machine, milling, and tracking trimming, scraping, polishing and other functions. ?The edge is the key to the edge of the plate must be straight, not push table saw blade size dislocation generated by the steps, to pressure post close, otherwise prone to edge and edge cracks, hand edge special glue best edge by hand, do not recommend the use of adhesive, heat is easy to fall off. ?2.: veneeringPlate thick sanding - selection of veneer veneer veneer cutting - seam - plate - will be put in the glue veneer panels -- into the hot pressing surface coating adhesive, edge trimming orSeveral key veneer veneer:The paste surface must be flat, no plate reinforcement, sag, such as holes, otherwise easy to bubble, separation;Veneer cutting cut straight seam tight, otherwise prone to crack;Glue to proper and uniform, too much glue easily through the glue, glue is too small easy to lack of glue, bubbling, separation;The temperature and time of pressing should be mastered accurately. ?If there's anything else you can't understand, leave a message for me and talk about it in detail.A sheet of thick sand light, XSUJN said very well, no longer Russell; on veneer cutting, add, in addition to the said, and sometimes in order to need to design and style, to make the M word, veneer cassion, twill and other flower shaped, but also need to use special wood cutting machine cut. The pattern can spell out such a beautiful symmetry.
1. edge:The manual or automatic edge banding machine edge, can also manually edge, no matter what kind of program are: edge, edge or edge glue - edgeband pressure post in edge - edge - on both sides of the extra redundant block edge trimming - dressing for automatic sealing machine, milling, and tracking trimming, scraping, polishing and other functions.The edge is the key to the edge of the plate must be straight, not push table saw blade size dislocation generated by the steps, to pressure post close, otherwise prone to edge and edge cracks, hand edge special glue best edge by hand, do not recommend the use of adhesive, heat is easy to fall off.2. veneer veneer:Plate thick sanding - selection of veneer veneer veneer cutting - seam - Sheet glue - coating adhesive on the veneer sheet surface into the hot pressing - trimming or trimmingSeveral key points of veneer veneer:The surface must be flat, and there must be no ribs, depressions, holes and so on, otherwise it is easy to bubbling and separating;Veneer cutting cut straight seam tight, otherwise prone to crack;Coating should be appropriate, even, too much glue, easy to penetrate, glue too little, easy to lack glue, bubble, separation;The temperature and time of pressing should be mastered accurately.
