Marble surface polishing color becomes dark no light how to restore the original
The ground side evenly sprayed K2, K3 drops, while using marble polishing, cleaning machine with red scouring pad, K2, K3 with the same amount of water drops onto the ground, using 175 RPM wiping machine weight 45KG start grinding, the surface effect of heat the material formed in the crystal surface after the crystallization of stone surface.Add: the whole ground maintenance treatment: if the porosity is large (stone sandstone, travertine marble etc.) to door besmear, after 12 hours, and then washing machine alternately to complete K2, K3 drops mill on the ground, K2-K3-K2-K3-K2 a total of five times, and then put on the white polishing pad, spray a small amount of K1 the potion, RE polishing time, in order to increase the surface hardness of the ground.Ground cleaning maintenance: when the surface of the stone to form crystal mirror, use the vacuum cleaner to suck ground residue and water, and finally the use of polishing pad polishing, the surface is completely dry, bright as a mirror, if the local damage can be the local maintenance, construction completion can always walk on. Note that some of the use of long stone ground height error is larger, this is because of the foundation settlement and external damage caused by factors such as. These floors, such as the reference 2m + 1mm flatness standards, it is difficult to achieve, only through grinding, grinding the focus of the higher part, you can adjust and reduce the flatness error.
1 tools / materials: multi-function brush machine, vacuum suction machine, three speed drying machine, dust mop, scouring pad, pad, marble, plate wire cloth, shovel bucket, water wax stains, all-around cleaning agent, crystal powder, K2, K3 and other hard. ,
Clean up the ground thoroughly and clean it with dry, clean ground.The stone surface cleaned, with marble glue to each stone above the small stone to repair the damaged point and raphe, the original stone with the color of marble near the glue to repair the damaged surface. Then use the slot machine dedicated to the original stone stone installation of the raphe re neatly cut slot, slot width, and then close the stone color on the marble glue to fill (Note: if you've already done raphe processing is new open without seam). Such as dry glue can do the next procedure must be repaired after the marble glue.The marble glue after drying and grinding grinding on the overall use of the ground machine, the whole horizontal grinding, grinding key caulking glue at the stone between (corner stone between) and close to the wall, decorative style, special shape at the edge of the stone floor to keep the overall smooth, polished finish first, re marble glue. Second, continue to complete the caulking and grinding, stone retreading machine with steel mill stone tablets from coarse to fine, (150 mesh, 300 mesh, 500 mesh, 800 mesh, 1000 mesh, 1500 mesh, 2000 mesh, 3000 mesh), is required to complete the eight time to polish the final ground overall smooth, then the steel wire cotton polishing, polishing to achieve the design requirements of the degree of brightness (70 degrees), no obvious gaps between the stones.
1-2 times a week to stone care machine with nano wool pad (Bai Jiedian) (such as a 300-400 high speed machine better) on the ground has been washed clean or spray a small amount of crystal surface maintenance agent or hard crystalline powder (hard crystalline powder to add water, water, water and humidity according to the dry weather should be more.) 1-2 grams per square meter. Apply the stone care machine and then grind to the light. Finally, push the dust off the ground with dust. Should be staged grinding, each 1-2 square meters. Cleaning pad should be kept clean, when there is too much powder will affect the effect; if found to be contaminated with the other side of the turn to use, until the two sides are stained with the replacement of a new. Depending on the area of work, with enough pads, the stain should be washed and dried before use. In the smooth dark ground, can be used to pad pad pad, the effect is better, but should pay attention to, the ground is not smooth, or the steel pad pollution will make the ground black
