Home > categories > Hardware > Wire > Where do I connect the green ground wires on my ceiling fan?
Question:

Where do I connect the green ground wires on my ceiling fan?

I have a Hunter 5 minute fan. I have four wires coming from my ceiling. Red, Black, White, and Bare Copper. The Fan has a Green Wire, Black Wire, White WIre,and a Black/White striped Wire. The Ceiling Plate also has green wire. I know to connect the black to black, red to black/white striped, white to white. But for the green and copper wires, do I connect the copper wire from the ceiling to the green wire in the ceiling plate and also to the green wire from the fan?

Answer:

Black (hot) to Black White (return) to White Bare (ground) to Green [Green wire can also be connected to metal box with Wire-Nut] Red (light) to Black/White wire (switch)[ in some cases Blue wire]. Page 8 Installation Manual (4-Wirine the Fan) All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national and local electrical codes. 4-1. Before attempting installation, make sure the power is still off. 4-2. To connect the wires, hold the bare metal leads together and place a wire nut over them, then twist clockwise until tight. For all these connections use the wire connectors provided. 4-3. Connect the bare or green ground wire (grounded) from the ceiling to the green ground wire (grounded) from the ceiling plate and the green ground wire from the fan. 4-4. Connect the white wire (ungrounded) from the ceiling to the white wire (ungrounded) from the fan. 4-5. Connect the remaining wires as follows: Dual Switch Wiring: ? The black wire (ungrounded) from the ceiling to the black wire (ungrounded) from the fan ? The black/white wire (ungrounded) from the fan to the wire (ungrounded) for the wall switch Single Switch Wiring: ? The black wire (ungrounded) from the ceiling to the black (ungrounded) and the black/white wire (ungrounded) from the fan CAUTION: Be sure no bare wire or wire strands are visible after making connections. 4-6. Turn the wire connectors upward and push them carefully back through the ceiling plate into the outlet box. 4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box
You are correct. With Romex? type house wiring the bare copper lead is the ground wire and should be connected with both of the green wires.
For the best answers, search on this site https://shorturl.im/avzAc After reading your additional details, It is my understanding that you only have the green wire on the mounting plate. You have no other ground wire from your house wiring, as well as none from your remote box wiring. You only have hot and neutrals. Don't worry about that wire. cap it off and tuck it away. Your house is too old to have a ground. It is a safety wire in case of a short / over current. It wont affect the fan working. If you had a bare wire coming out of the box in your house you would connect it there.
This Site Might Help You. RE: Where do I connect the green ground wires on my ceiling fan? I have a Hunter 5 minute fan. I have four wires coming from my ceiling. Red, Black, White, and Bare Copper. The Fan has a Green Wire, Black Wire, White WIre,and a Black/White striped Wire. The Ceiling Plate also has green wire. I know to connect the black to black, red to black/white striped,...
As typical color coding goes in 110/120 volt A/C; Black = hot lead White = neutral Green = ground In house wiring the ground is typically bare and has no coating. Typically the fan and the mounting plate will have green wires to ground out the fan and the electrical box. If you have a ground wire (bare copper wire) you should hook to there. Update - - - Curtis is right, below this post. Your box is not set for a ground. Being that old of a house there is no telling what mods have been done. The neutral (white) and the ground (green or bare copper) are the same but different. The ground goes to the ground at your house. The neutral is the return to source (generating station). The ground helps make the electricity go the path of least resistance as soon as possible in the case of a short.

Share to: