How to assemble and disassemble the wardrobe?
The preparation before installation should be done well:When you look at a wardrobe, the salesperson will ask for information about your home decoration. If you have not yet completed the decoration on the ground, you should ensure that the original ground level in the room, if you need to find a large drop, mud master to quell. Smallpox also requires level, so that wardrobe can be avoided due to the installation of non vertical, horizontal and lead to cabinets, cabinets and wall, ceiling stay.Tip: if you want to use the wardrobe to do wall type wardrobe, it is recommended that you do not install the wardrobe L position mounted skirting line, even if the baseboard has been installed, the door installation, the master will also remove you.
Erection of cabinets and post treatment:1, after the assembly of the cabinet body, before placing the designated location, first put the cabinet location clean, check whether the wall and the ground intersect whether there is irregularities. ?On the 2, the cabinet body is set up when the ground floor good skin protection, protection of the region to achieve half swing cabinet position, when the cabinet body is pushed to the designated location 2/3, will push the upper part of the cabinet body inclined, underground out of cardboard. This method is relatively heavy and largeCabinet body ?3, the cabinet body is moved to the specified position of the 2/3, the corresponding field relatively straight side wall closing plate is arranged in the cabinet body, because can not see the smooth tapping screw is directly fixed on the cabinet body is closing plate should pay attention to, must be flat seal.
Backplane mounting:After the assembly of the cabinet is complete, the central line for the backboard is assembled when the intersecting plate is laid.1. When assembling the backboard, the angle of the cabinet body must be straightened first. In the case of the ground relative level, the most commonly used method is to use the steel wire ruler to measure the diagonal of the cabinet body. The control drawings on the backplane structure, a cabinet on the back (because the back in the production of the joint will be docked in the panels of the center line at the largest size) and then will be on both sides of the back board is inserted into the backplane slot two outside, and then put the midplane. According to the original plan good back fixed line extension to the corresponding position on the back plate, with a 3mm twist drill to drill a hole in the back screw position, when installing screws to prevent the cracking of the cabinet body. (when the two back together the seam, can the gap between the two nozzle alignment back drilling, 3mm drilling screws with two back then.) ? ?There are two kinds of methods of peripheral plate back 2, normal:A. half cell; half groove refers to a figure of 7 in the gap behind the medial peripheral board, backplane on half groove with nails or screws fixed. ?The U groove is positioned at the inner part of the outer side of the outer baffle plate to open the gap, and the back plate is arranged in the gap and is clamped and fixed on both sides of the groove, and the b.U groove is clamped and fixed.
Use the cloth pad floor, starts from the side wall wide end assembly, the wide side flat on the ground (700mm distance from the wall). First fill in plate three a rubber plug, flat on the cloth, check the hole spacing consistent with the drawings, and put on three in one single link. Focus on product structure, all horizontal intersect fixed position is three in one connection, the embedded three one screw mounted on the connecting plate, in depth is subject to the lower part of the rubber sleeve screw.When assembling the principle is based on the middle installed to around, each plate encased position is provided with a screw hole and the eccentric hole will be installed screw plate alignment screw hole plate on the corresponding and inserted by eccentric hole saw screw head is about 5mm then, the eccentric wheel into the hole (note that an eccentric wheel arranged at the eccentric wheel surface has a direction of the arrow to alignment screw hole), clockwise to tighten, such two panels can intersect together even tight. In the assembly process, is to take down the back toward the assembly, a blank position in front of the cabinet body, should be installed after the internal structure identical to the previous blank position height items below the mat (usually with the cabinet foot plate or the closing plate), then assemble the external plate, finally the cabinet foot line.
