The diameter of 20 solid round steel bend into a circle, what machine bending?
Steel hoop benderConstruction: steel bending machine is suitable for bending stirrups, the bending angle can be adjusted arbitrarily, the structure is similar to the bending machine.Working principle: motor powered by a pair of wheels and two straight gear reducer, the eccentric disc rotates. The eccentric disc drives two connecting rods through an eccentric hinge, each connecting rod is hinged with a rack, so the rack moves reciprocally along the slideway. The rack also drives the gear to make the working disc reciprocate in a certain angle. The work disc has two axle holes, the central hole is inserted into the central shaft, and the other jack is arranged on the shaft. When the work disc is rotated, the central shaft and the forming shaft rotate together. The same principle of the steel bending machine can bend the steel bar into the required stirrups.
Hydraulic steel bar cutting and bending machineThe hydraulic steel bar cutting and bending machine is a dual-purpose machine which uses hydraulic technology to cut and bend steel bars. It has high automation and convenient operation.Structure: hydraulic type steel bar cutting and bending machine mainly consists of hydraulic transmission system, cutting mechanism, stubborn mechanism, engine, airframe and so on.Working principle: an electric motor drives two sets of plunger hydraulic pumps, one group pushes off the piston, and the other drives the rotary hydraulic cylinder to drive the rotary working disc to rotate.Cut off the working principle of mechanism in cutting piston is arranged in the middle column and the center of the valve spring, in turn, due to the action of the spring, the middle hole make the center column left valve hydraulic cylinder, high pressure oil is also from the eccentric shaft road to tank. In the cut, a human powered piston, the center hole center column valve blocked the hydraulic cylinder, the plunger pump to the hydraulic cylinder through high pressure oil into the oil valve, high pressure to push the piston movement, the piston drives the cutter to cut tendons. At this point, the thrust of the pressure spring is greater than the pressure in the hydraulic cylinder, the valve will return to its original position, and the hydraulic oil will flow along the oil channel of the central oil hole back into the tank. The return stroke of the piston is achieved by the rebound force of the plate spring.
Gear type steel bar benderStructure: gear type steel bending machine mainly consists of several motors, gear reducer, work mechanism and electrical control system. It changed the traditional worm gear drive, and increased the angle automatic control mechanism and brake device.Operation principle: the gear type steel bar bender is driven by a motor with braking, which drives the working disc to rotate. The two inserting seats on the left and right of the working mechanism can be adjusted by the hand wheel without bending, and can be bent and bent with different specifications of the steel bar. The angle is controlled by several different institutions and primary angle limit pin with each other and realize. When the steel bar is bent to the preselected angle, the limit pin touches the travel switch, causes the motor to stop and reverse, recover to the original position, and complete the bending process of the steel bar. In addition, the electric control system also has the characteristics of inching, automatic state, two-way control, instantaneous braking, emergency stop, rapid system short circuit protection, motor overheat protection, etc..
Worm and worm type steel bar benderStructure: worm and worm type steel bending machine, mainly each family, motor, transmission system, work mechanism (work disk, insert seat, gripper, shaft, etc.) and control system. A walking wheel is arranged under the frame for easy movement.Working principle: the power of the motor is rotated by the V belt pulley, the two straight gear and the worm gear rod, and then drives the working disk to rotate. The working disk usually has 9 shafts, the center hole is used to insert the central shaft, and the 8 hole seats around each have 6 holes, which are used to insert the retaining shaft. In order to move the reinforcing steel bar, two times of each work table is also provided with a feeding roller. When working, according to the bending shape of the steel bar, the square of the reinforcing steel bar is arranged between the central axis of the work disc and the corresponding forming shaft, and the inner side of the iron block is blocked. When the working disc is rotated, one end of the reinforcing bar is prevented from rotating by the iron blocking shaft, the central shaft position is fixed, and the forming shaft is rotated in an arc direction around the central shaft, and the reinforcing bar is bent.As a result of the specification, the bending diameter of the steel bar shall be no less than 2.5 times of the diameter of the steel bar when it is taken as a 180 degree bending hook. Therefore, the center shaft is also made into 16~100mm in 9 different specifications to meet the requirements of bending different diameter steel bars.
Or a bar bending machine machine, the installation of a 20cm diameter on the rotating die on the line, available 20mm manual welding steel die making.
