What is the use of ceramic tile?

What is the use of ceramic tile?

What is the use of ceramic tile? Tiles are a widely used decorative building materials, because of its beautiful appearance and get people's favor. In many people the impression that the tiles are cemented together, so that a reference to the tiles we will think of cement, and even think of some of the ceramic tile after falling off. In fact, the installation of tiles can not use cement, tile glue is a very good cement alternatives, ceramic tile strong glue, not only sticky tiles, can also be used for gypsum board and fiberboard installation, is an application Very wide building materials. Then we take a look at the tile information. Tile glue, also known as tile adhesive or adhesive, viscose mud and other names, is a modern decoration of the new material, instead of the traditional cement and sand, glue mortar is several times the cement mortar can effectively paste large Of the tile stone, to avoid the risk of brick. Good flexibility to prevent the production of hollowing. Mainly used for pasting tiles, tiles, floor tiles and other decorative materials, widely applicable to the inside and outside the wall, floor, bathroom, kitchen and other architectural finishes. Its main feature is the high bonding strength, water resistance, resistance to freeze-thaw, anti-aging performance and construction convenience, is a very good bonding material. In contrast to cement, tiles have many advantages, such as the use of ceramic tile can be more space than the use of cement, ceramic tile as long as a thin layer on it, and cement will be thicker; tile adhesive strong, if the construction Process standards, then the tile is very strong sticky; but also reduce the waste, no toxic additives, in line with environmental requirements.

More than 4 can lead to the sizing after sizing. In the construction of trimming when careful not to squeeze too much, or easily lead to foam foam rod deformation, then the foam rod will gradually recover, resulting in the overall sealant muster; construction within the scope of the construction to extend the correction time, Operation, the use of scraper from the bottom of the seam up to trim, to avoid curing the strip surface is uneven and a small amount of sagging; due to the different types of profiles on the market, it is recommended that customers in the use of each batch of plastic products before their own simple Of the adhesive test, in recognition of product quality can be widely used, which is to ensure the quality of the project at the same time also protect their own interests. Tile glue a lot of advantages, relative to the traditional materials such as cement in terms of advanced technology, saving material consumption, to ensure the quality of the project and conducive to environmental protection, is a good choice in the housing decoration. But this does not mean that tiles are the best choice for all people, on the one hand the current market tile unit cost is higher than the cement, on the other hand also take into account the construction process, its construction technology requirements than Cement should be high, if the use of ceramic tiles improper, the effect will be greatly discounted. So we choose to use cement or magnetic glue must be based on their actual situation to choose the best products for the better. Learn more about tile information click on id

2, de-alcoholated TC: curing shrinkage is small, water immersion off small, most of the substrate without corrosion; on the fluorocarbon profiles, steel and white marble, poor adhesion; at high temperatures, due to the reaction rate Fast, resulting in the formation of alcoholic small molecules can not be volatile in time, and the formation of bubbles affect the construction quality. Deoxime type TW: good adhesion can be in the appropriate high temperature construction, will not produce bubbles; copper and mirror industry with micro-rot. And shrinkage than alcohol type. Use restrictions: non-structural adhesive prohibited for use in structural assembly; Should not be used for oozing grease, plasticizer or other solvent building materials surface; should not be used for frost or wet surface, long buried in the underground or long-term immersion occasions; should not be used for paint the surface may be due to paint cracking or Peeling off caused by sealing failure; should not be used for direct contact with food or vulnerable to mechanical wear; not suitable for building materials, surface temperature below 4 ℃ or higher than 40 ℃ when the construction. 3, deacidification type: acid glue should not be used for cement, stone, Because the acid to produce acetic acid curing, and cement, stone and other alkaline materials on the surface reaction to form a chalk-like material, and cause off; substrate expansion coefficient is larger, with displacement or vibration, plastic construction (1) high temperature sizing, high temperature curing; curing speed too fast, the use of high-temperature, high-temperature curing, (2) sizing too thin, less than 6 mm; (3) foam rod (bar) damage caused by foaming (opening), the release of methanol from the colloid in the rate of bleeding, so that the gasification of methanol after the gasification; Type foam); there is water; foam material is incompatible, chemical reaction; (4) sizing irregular, repeated scratched.

Use: the construction of the wall to be wet (outside the wet dry), and to maintain a certain degree of flatness, uneven or extremely rough parts of the application of cement mortar and other materials leveling; grass-roots must remove the floating ash, oil, wax, so as not to affect the stick Knot tiles in 5 to 15 minutes after the move can be corrected. Water-cement ratio of about 1: 4, after mixing the binder should be used within 5 to 6 hours (the temperature is about 20 degrees); the mixed adhesive applied to the back of the adhesive brick, and then Press hard, until the plain so far. Due to different materials and the actual consumption of different, generally at least about 4.5 to 6 kg per square meter, paste thickness of about 2 ~ 3mm. Use of common sense: 1, deacetal type: vulcanization speed, transparency is good, but in the curing process Release of acetic acid; with a pungent odor, but also on the metal, coated glass and some inorganic materials corrosion.