What is the inner diameter of the drain basin of the desktop washbasin?
The following is my personal summary of the point of view:
1, wash basin hot and cold water triangle valve installation elevation of 45 cm, the installation should consider the factors of its decorative floor tiles. The distance between the valve should not be too far, generally around 15 cm, or will be exposed outside the basin, there is a beautiful.
2, the basin of the drain is generally 15 cm away from the wall, not too close to the wall, otherwise the drain will be exposed, affecting the appearance. Too far and easy on the vertical basin of the drain, can not be installed.
3, the mirror is generally not close to the basin installed.
4, fixed wash basin before the first installation of the faucet, do not wait until the basin is fixed and then installed. If it is fixed with silicone, it is easy to walk
PT-type pillar wash basin stable:
???? A draw the vertical line according to the center of the drainage pipe, the pillars will be established, the washbasin on the pillar, so that the center of the basin against the vertical line, leveling the basin after the fixed hole position. While the pillars in the ground position to do the mark. Press the wall mark tick into φ10 × 80mm hole, planting fixed bolts. Will be placed on the ground pillar mark gray gray cream, stabilize the pillars and wash basins, fixed bolts plus rubber pads, eye socket, with nuts screwed to moderate elasticity. Once again face basin surface leveling, pillars straight. The pillars and the basin contact with the pillars and the ground contact with white cement gouge trowel.
???? B PT-type pillar-type washbasin to the drainage pipe connection method with reference to the wash basin supply and drainage pipe installation.
?? I do not know what you want to do with this? If a hydropower installation workers are not equipped with pots, he is not mixed.
Wash basin stable:
????A washbasin stent installation: should be in accordance with the center of the drainage pipe in the wall to draw vertical lines, from the ground up to the provisions of the height, draw the horizontal line, according to the width of the basin in the horizontal line to draw the stent position of the cross line. Press the mark tick into φ30 × 120mm hole. Wash the basin stent. And then placed in the stent on the basin flat, find positive. Hook the hook in the basin under the fixed hole, tighten the fixed frame bolt, looking for flat. Wash basin drain connection:
????A S-type water pipe connection: should be in the bottom of the basin outlet deduction of lead oil, wrapped in a little linen. The water will be twisted on the drain on the drain, elastic moderate. And then the lower part of the water storage section of the lower end of the oil pan inserted in the drain pipe mouth, the pads on the connection in the trap, the lock mother tightened after the straight to find. And then wrench to the tight temper. With the putty will be sewer eyes tight, smooth.
????B P-type access to the water pipe connection: should be in the bottom of the wash basin under the deduction of lead oil, wrapped a little linen. The water will be twisted on the drain line, elastic moderate. And then save the water bend the need for length with a good line. The lock mother and mouth care back to the back of the set in the bow, wrapped in the end of the oil pan rope, test the height of the right is appropriate, if not appropriate to adjust the section, and then put the pad on the lock, the lock mother Twist to moderate elasticity. The mouth of the mouth to fill the vanity to the wall after leveling, according to real. Remove the overflow of putty and wipe the wall. Will be exposed at the outlet of linen clean.
Washbasin Parts Installation:
???? A installation of the basin outlet: first into the mouth of the root of the mother, eye socket, rubber pad unloaded, the pad will be put into the wash basin after the toilet drain, the overflow in the sink to the overflow in the basin outlet Oral eye. Plus padded putty pad, put on the eye socket, bring the root of the mother, and then self-made wrench stuck in the mouth of the cross bar, with a flat wrench on the root of the mother to the elastic moderate.
???? B install the basin faucet: the first water nozzle root mother, lock the mother unloading, in the mouth of the sink pad put a good putty, insert the basin to the water hole, the following and then put the pads on the eye socket, with the root left hand holding down the mouth , The right hand with a self-made witch dead wrench lock tight to moderate.
