What welding rod does 20CrMnTiH use?
1, 20CrMnTi is steel carburizing, carburizing steel is usually carbon, low carbon steel 0.17%-0.24%. The car with the drive gear is in manufacturing. The hardenability of Shanghai Kai Xin steel to provide pictures2 Cr Mn Ti carbon steel and permeability, the higher hardenability, the quenching conditions, with high strength and toughness, especially with high strength and impact toughness of.20CrMnTi steel surface carburizing hardening. Good processability, small deformation, anti fatigue performance is good. Use: for the gear, shaft, piston type accessories. For cars, aircraft of various special parts.3, the characteristics and scope of application: is the good performance of carburizing steel, high hardenability, carburizing after quenching with hard and wear-resistant surface and tough heart, has high low-temperature impact toughness, weldability medium, normalizing machinability is good. Used to manufacture the important parts, such as gears, gear rings and gear shafts, that bear high speed, medium or heavy load, impact and friction, which are less than 30mm. 18CrMnTi is widely used as a substitute for steel, carburized parts, in the automotive industry for the tractor. Under the high-speed section below 30mm. In heavy load or impact. And the important carburized parts, such as gear shaft. The friction ring gear. The gear shaft. The spindle. Sliding bearing. The crosshead. Claw clutch worm. Etc..4, J857Cr low alloy high strength steel welding rod, 857Cr low-alloy high-strength steel welding rod comply with: GB E8515-G equivalent: AWS E12015-G5. Description: J857Cr is low hydrogen and sodium type skin with low alloy and high strengthPreheat 200 before welding and 500-700 (or dark red) after soldering
20CrMnTi is steel carburizing, carburizing steel is usually carbon, low carbon steel 0.17%-0.24%. The car with the drive gear is in manufacturing. The hardenability of Shanghai Kai Xin steel to provide picturesCr Mn Ti carbon steel permeability, the higher hardenability, the quenching conditions, with high strength and toughness, especially with high strength and impact toughness of.20CrMnTi steel surface carburizing hardening. Good processability, small deformation, anti fatigue performance is quite good. Use: for gear. Shaft, piston type accessories. For cars, aircraft of various special parts. The characteristics and applicable scope: good performance of carburizing steel, high hardenability, carburizing after quenching with hard and wear-resistant surface and tough heart, has high low-temperature impact toughness, weldability medium, normalizing after the machinability is good. Used to manufacture the important parts, such as gears, gear rings and gear shafts, that bear high speed, medium or heavy load, impact and friction, which are less than 30mm. 18CrMnTi is widely used as a substitute for steel, carburized parts, in the automotive industry for the tractor. Under the high-speed section below 30mm. In heavy load or impact. And the important carburized parts, such as gear shaft. The friction ring gear. The gear shaft. The spindle. Sliding bearing. The crosshead. Claw clutch worm. Etc..Welding technology information network weld8 provides answer J857Cr low-alloy high strength steel welding rodJ857Cr low alloy high strength steel welding rod meets: GB E8515-G: AWS E12015-G: J857Cr is low sodium hydrogen type leather with low alloy and high strengthPreheat 200 before welding and 500-700 (or dark red) after soldering
20CrMnTi is steel carburizing, carburizing steel is usually carbon, low carbon steel 0.17%-0.24%. The car with the drive gear is in manufacturing. The hardenability of Shanghai Kai Xin steel Cr Mn Ti steel to provide pictures infiltration of carbon steel, the higher hardenability, the quenching conditions, with high strength and especially with high toughness, low temperature impact toughness of.20CrMnTi steel surface carburizing hardening. Good processability, small deformation, anti fatigue performance is quite good. Uses: used for gear, shaft, piston type accessories. For cars, aircraft of various special parts. The characteristics and scope of application: performance good carburizing steel, high hardenability, carburizing after quenching with hard and wear-resistant surface and tough heart, has high low-temperature impact toughness, weldability medium, normalizing machinability is good. Used to manufacture the important parts, such as gears, gear rings and gear shafts, that bear high speed, medium or heavy load, impact and friction, which are less than 30mm. 18CrMnTi is widely used as a substitute for steel, carburized parts, in the automotive industry for the tractor. Under the high-speed section below 30mm. In heavy load or impact. And the important carburized parts, such as gear shaft. The friction ring gear. The gear shaft. The spindle. Sliding bearing. The crosshead. Claw clutch worm. Etc.. J857Cr high strength low alloy steel electrode J857Cr high strength low alloy steel electrode line: GB E8515-G AWS E12015-G: Description: J857Cr is a high strength low alloy welding preheating low sodium hydrogen coating 200 after welding tempering 500-700 (or dark red)
