Screen film sticking method: 1, it is better to prepare adhesive tape paper folded as follows (used for sticking dust) first power off before sticking the film. It is better to stick some gaskets on the bottom of the screen because a lot of laptop screens might not fold to 180 degrees, and it is better to fix the screen. First clean the screen to be filmed, which should be totally cleaned, or there will be small bubbles due to dust. First take out screen film to make sure whether the size fits the screen. You will see small stickers marked 1 and 2 on protective film after confirmation, first peel off the sticker marked 2 and then turn over the screen, and film marked 1 should be sticked on the screen. First uncover a small corner, try to parallel one side of the film with laptop screen shell along one side, slowly put down. Because the film has electrostatic adsorption ability, it will automatically be adsorbed onto the screen. There may be two cases during the sticking process: 1, there will be some small dust adsorbed on the film, so there will be bubbles after being sticked up. Solution: use the adhesive tape prepared before, find the place where there is small dust, and stick off the dust with tape. 2, If there are small bubbles, first uncover the film slightly back, and then stick back after squeezing out the bubble. If it does not work, you can use the wiping cloth, which is supposed to work out after slowly wiping past the screen. Continue to stick with patience, deal with small bubbles while sticking until completion. Pay attention to end up at a corner when ending, and then tear open the label marked 2.
1. First, tool material preparation: Usually the essential materials for sticking film for computers include: Hard card (ID card, bank card or other hard cards), cleaning solution, wide adhesive tape, wiping cloth, film and computer. Among which,the wiping cloth should be made of materials with good flexibility, which can effectively prevent scratches when wiping the computer screen. 2, wipe the screen with wiping cloth along one direction to clean the dirt and dust on the screen. 3. Uncover the fim and observe carefully, you will find that film is composed of three layers, among which the topmost layer is used for protection and the middle layer is the real film. At this time, uncover the topmost layer. 4 and then slightly uncover the bottom layer, stick on computer screen in corresponding position, take out the bottom layer continuously at the same time. 5, the next step is the most important part, namely eliminate the bubbles in computer film. Stick the hard card closely on the top of the film, priority processing the relatively large bubble during promoting course, slowly push the bubbles to to the edges of computer screen, and then squeeze out the gas. Push toward the nearest place from the edge when pushing. 6, finally squeeze the upwarped parts around the film to ensure that the film is closely integrated with the computer screen. At the same time, if the film contains dirt or dust, they also need to be cleaned up in this step.
The first step: choose dustfree room to stick film. The new machine generally only needs to clean the scattered dust with wiping cloth in screen protective film set, while the old machine first needs to clean the screen with cleaning set and air the screen before sticking film; the second step: first contrast the size of the screen with the film, protective film is usually 2-3 mm smaller than LCD screen, align the screen with the side labeled 1, pick up the label 1, stick a cornerfirst, continue from left to right; the third step: the film of label1 is protection layer rather than the use layer, peel off the film of label 1 slowly from the bottom, flat the contact surface of protective film and LCD screen with flannel at the same time. Usually screen protective films of OK8 series have electrostatic adsorption function, which can automatically adhere to the LCD screen; the fourth step: after sticking the protective film up, tear off the above film of label 2, and then complete the entire process. If there is a deviation during film sticking process, OK8 protective film can also be reopened and then slowly sticked. Pay attention to the bubbles when sticking for the second time, which will generally disappear automatically within a week; if there are foreign matters and dust on the protective film due to storage for a long time, you can clean it with a cloth stained appropriate cleaning solution.
First step of film sticking: aim the film marked ① at the screen and pull the ① layer of release liner label, slowly tear a part of this layer, pay attention not to touch the adsorbed layer (middle layer) of the protective?film with fingers. Second step of film sticking: aim the adsorbed layer at the screen corner, make sure that the position is aligned, smooth the film carefully while tearing off the backing layer ① release liner. Because present protective film has electrostatic automatic adsorption function, generally it does not need be ironed too much. The action should be slow when sticking the film, and it is recommended to start sticking along the long side of the screen, from point to line, from line to surface successively
