Question:
Could I Use Iron-On Letters On Fluffy Fabric?
I want to use iron on letters on this blanket, but the blanket is wayy soft and fluffy so I am unsure if it would ruin it.
Answer:
There are actually 2 definitionsI'll give you the one that is generally recognized by the bike industryButting is where that ends of the tube are thicker than the centerIn steel frames this saves weight and radically improves responseIn aluminum, it just saves weight- if aluminum is allowed to flex it will eventually fail So, in general, double butting is where the ends of the tube are double the thickness of the center of the tubeTriple butting is where the butts are still double the thickness but the length of the butt is 3 times the diameter of the tubeStrangely enough, most butts are at LEAST 3 times the diameter of the tube, so the actual difference between the two could benothingEDIT: Guys, I mentioned there were 2 definitions, I gave oneThe definition you provided is the classic one that is rarely referred to nowThis classic referral never held water insofar that many tubemakers (outside of Reynolds and Columbus) were unable to butt both ends of a tube who then referred to the thickness of the butt as single or double buttingRefer to technical info provided by bicycle frame makers such as Kinesis for a further explanation.
There are actually 2 definitionsI'll give you the one that is generally recognized by the bike industryButting is where that ends of the tube are thicker than the centerIn steel frames this saves weight and radically improves responseIn aluminum, it just saves weight- if aluminum is allowed to flex it will eventually fail So, in general, double butting is where the ends of the tube are double the thickness of the center of the tubeTriple butting is where the butts are still double the thickness but the length of the butt is 3 times the diameter of the tubeStrangely enough, most butts are at LEAST 3 times the diameter of the tube, so the actual difference between the two could benothingEDIT: Guys, I mentioned there were 2 definitions, I gave oneThe definition you provided is the classic one that is rarely referred to nowThis classic referral never held water insofar that many tubemakers (outside of Reynolds and Columbus) were unable to butt both ends of a tube who then referred to the thickness of the butt as single or double buttingRefer to technical info provided by bicycle frame makers such as Kinesis for a further explanation.
Tubing manufacturers feel that a frame needs different amounts of reinforcement in different areasSo to optimize frame tubing now comes in five different butting arrangements: none, single, double, triple, and quadrupleA tube without a butt has constant wall thickness; it is called a straight gage tubeA single butted tube is thicker at one end; double butted tubes are thicker at both ends (each end of the same thickness); triple butted tubes have ends of unequal thickness; and quadruple butted tubes have ends and midsections of varying thickness.
Blah.your both rightDifferent welders claim what they call double butting to be butting a second time to make a more gradual transition within the tube to avoid a harsh overbutting.Certain makers butt the top and bottom of the tube where some butt more evenly.This is simply custom butting however they please.Sheldon 's site is great but no one knows everything and no one can tell a frame maker what to define or how.[unless it is a patented design]Yet they may try to and all are allowed to have an opinionA triple butted frame,be it tubes or stays butted,is for racing only in my opinion as hard rock scrapes or hits can cause the frame to failAlso,I may add that I'm used to hearing 6000 series aluminum triple butted but not 7000 series.It just sounds off.[shruggs] Just my two cents worth.
This is probably not a good ideaMost blankets these days are made of synthetic fibers, and if you use the heat that the iron on letters require, the blanket will meltIn addition, you really need very smooth fabric in order for the iron on to adhereYou MIGHT try embroidering the letters on with yarnNot the iron on letters, it's very hard to pierce the fabric of thoseEither completely embroider with yarn, or cut out letters from fleece or felt and use yarn to sew them on.
Tubing manufacturers feel that a frame needs different amounts of reinforcement in different areasSo to optimize frame tubing now comes in five different butting arrangements: none, single, double, triple, and quadrupleA tube without a butt has constant wall thickness; it is called a straight gage tubeA single butted tube is thicker at one end; double butted tubes are thicker at both ends (each end of the same thickness); triple butted tubes have ends of unequal thickness; and quadruple butted tubes have ends and midsections of varying thickness.
Blah.your both rightDifferent welders claim what they call double butting to be butting a second time to make a more gradual transition within the tube to avoid a harsh overbutting.Certain makers butt the top and bottom of the tube where some butt more evenly.This is simply custom butting however they please.Sheldon 's site is great but no one knows everything and no one can tell a frame maker what to define or how.[unless it is a patented design]Yet they may try to and all are allowed to have an opinionA triple butted frame,be it tubes or stays butted,is for racing only in my opinion as hard rock scrapes or hits can cause the frame to failAlso,I may add that I'm used to hearing 6000 series aluminum triple butted but not 7000 series.It just sounds off.[shruggs] Just my two cents worth.
This is probably not a good ideaMost blankets these days are made of synthetic fibers, and if you use the heat that the iron on letters require, the blanket will meltIn addition, you really need very smooth fabric in order for the iron on to adhereYou MIGHT try embroidering the letters on with yarnNot the iron on letters, it's very hard to pierce the fabric of thoseEither completely embroider with yarn, or cut out letters from fleece or felt and use yarn to sew them on.
